EXACTLY HOW TO INSTALL A BATH TUB: INSTALL AN ACRYLIC TUB AND ALSO TUB SURROUND

Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround

Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround

Blog Article

Click For More Info

How do you actually feel on the subject of Tools You Need to Install a New Bathtub ?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a tub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is also a reasonably difficult project. If the old tub is readily easily accessible, the job can relocate immediately; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the work as well as fit trying it. Instead of employing a service provider to take over a halfway-completed project, it is better to consider employing one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This write-up will certainly aid you set up a new tub in your bathroom if you have currently gotten a brand-new tub and don't need to transform the plan of your previous water system pipes.
Your tools and also product list ought to comprise the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you require to replace old taps with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing taps can be quite bothersome because of the restricted gain access to that is often the instance.
    Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from turning throughout this process. Once the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
    Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

    Fitting New Touches


    If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a link to the existing supply pipelines.
    If you need to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next, place the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in location in between the tap as well as the sink. Safeguard the tap in place with the supplier offered backnut. As soon as the tap is safely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous kind ought to be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Mounting the Bath tub


    Using the two wood boards under its feet, position the tub in the called for position. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little factors.
    The following goal is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the tub until the spirit level checks out degree.
    To mount taps, fit all-time low of the outermost adaptable tap connector to the appropriate supply pipe by making a compression join; then do the exact same for the other tap.
    Turn on the water and also check all joints and new pipework for leaks as well as tighten them if needed. Fill up the tub as well as likewise inspect the overflow electrical outlet and also the typical electrical outlet for leaks.
    Lastly, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has been used at least when as this will certainly resolve it right into its last setting.

    Planning for the Setup


    First of all, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to avoid stress on the bathtub.
    Fit the adaptable faucet connectors to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
    Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its last position.

    Tiling Around the Tub


    In the area where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, triggering the water to penetrate the wall in between the bath and also the tiling, leading to issues with dampness as well as feasible leaks to the ceiling listed below.
    You can choose from a range of coloured sealers to blend in your components and fittings. They are marketed in tubes and cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to permit the motion experienced when the bathtub is in use. The sealer can fracture relatively very early if you do not consider this activity before sealing.
    Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant glue and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I stumbled upon that entry on Tools You Need to Install a New Bathtub while surfing around the internet. Sharing is nice. You never know, you will be doing someone a favor. Bless you for your time. Visit again soon.




    This Resource


    Report this page